Saturday 2 February 2013
How to hack online ip address and do anything with your control tutorial
Hi guys. First of all, I want to say that I
didn't make this tutorial myself, I found it
on Hacking Library
If it's not authorized to post this kinda
tutorials here, or if it has already been
post, then I'm sorry to say useless
things : )
the tutorial looks like that :
Introduction
1. Welcome to the basic NETBIOS
document created by aCId_rAIn. This
document will teach you some simple
things about NETBIOS, what it does, how
to use it, how to hack with it, and some
other simple DOS commands that will be
useful to you in the future. THIS
DOCUMENT IS FOR NEWBIEZ ONLY!!! If
you are NOT a newbie then don't go any
farther reading this because if you're
smart enough you probably already know
it all. So don't waste yourt time reading
something that you already know.
1. Hardware and Firmware
1a. The BIOS
The BIOS, short for Basic Input/Output
Services, is the control program of the
PC. It is responsible for starting up your
computer, transferring control of the
system to your operating system, and for
handling other low-level functions, such
as disk access.
NOTE that the BIOS is not a software
program, insofar as it is not purged from
memory when you turn off the computer.
It's
firmware, which is basically software on a
chip.
A convenient little feature that most BIOS
manufacturers include is a startup
password. This prevents access to the
system until you enter the correct
password.
If you can get access to the system after
the password has been entered, then
there are numerous software-based BIOS
password extractors available from your
local H/P/A/V site.
NETBIOS/NBTSTAT - What does it do?
2. NETBIOS, also known as NBTSTAT is a
program run on the Windows system and
is used for identifying a remote network
or computer for file sharing enabled. We
can expoit systems using this method. It
may be old but on home pc's sometimes
it still works great. You can use it on your
friend at home or something. I don't care
what you do, but remember, that you are
reading this document because you want
to learn. So I am going to teach you. Ok.
So, you ask, "How do i get to NBTSTAT?"
Well, there are two ways, but one's faster.
Method 1:Start>Programs>MSDOS
PROMPT>Type NBTSTAT
Method 2:Start>Run>Type
Command>Type NBTSTAT
(Note: Please, help your poor soul if that
isn't like feeding you with a baby spoon.)
Ok! Now since you're in the DOS
command under NBTSTAT, you're
probably wondering what all that crap is
that's on your screen. These are the
commands you may use. I'm only going
to give you what you need to know since
you are striving to be l33t. Your screen
should look like the following:
NBTSTAT [ [-a RemoteName] [-A IP
address] [-c] [-n]
[-r] [-R] [-RR] [-s] [-S] [interval] ]
-a (adapter status) Lists the remote
machine's name table given its name
-A (Adapter status) Lists the remote
machine's name table given its IP
address.
-c (cache) Lists NBT's cache of remote
[machine] names and their IP addresses
-n (names) Lists local NetBIOS names.
-r (resolved) Lists names resolved by
broadcast and via WINS
-R (Reload) Purges and reloads the
remote cache name table
-S (Sessions) Lists sessions table with
the destination IP addresses
-s (sessions) Lists sessions table
converting destination IP addresses to
computer NETBIOS names.
-RR (ReleaseRefresh) Sends Name
Release packets to WINS and then, starts
Refresh
RemoteName Remote host machine
name.
IP address Dotted decimal representation
of the IP address.
interval Redisplays selected statistics,
pausing interval seconds between each
display. Press Ctrl+C to stop redisplaying
statistics.
C:\WINDOWS\DESKTOP>
The only two commands that are going to
be used and here they are:
-a (adapter status) Lists the remote
machine's name table given its name
-A (Adapter status) Lists the remote
machine's name table given its IP
address.
Host Names
3. Now, the -a means that you will type in
the HOST NAME of the person's computer
that you are trying to access. Just in case
you don't have any idea what a Host
Name looks like here's an example.
123-fgh-ppp.internet.com
there are many variations of these
adresses. For each different address you
see there is a new ISP assigned to that
computer. look at the difference.
abc-123.internet.com
ghj-789.newnet.com
these are differnet host names as you
can see, and, by identifying the last
couple words you will be able to tell that
these are two computers on two different
ISPs. Now, here are two host names on
the same ISP but a different located
server.
123-fgh-ppp.internet.com
567-cde-ppp.internet.com
IP Addresses
4. You can resolce these host names if
you want to the IP address (Internet
Protocol)
IP addresses range in different numbers.
An IP looks like this:
201.123.101.123
Most times you can tell if a computer is
running on a cable connection because of
the IP address's numbers. On faster
connections, usually the first two numbers
are low. here's a cable connection IP.
24.18.18.10
on dialup connections IP's are higher, like
this:
208.148.255.255
notice the 208 is higher than the 24 which
is the cable connection.
REMEMBER THOUGH, NOT ALL IP
ADDRESSES WILL BE LIKE THIS.
Some companies make IP addresses like
this to fool the hacker into believing it's a
dialup, as a hacker would expect
something big, like a T3 or an OC-18.
Anyway This gives you an idea on IP
addresses which you will be using on the
nbtstat command.
Getting The IP Through DC (Direct
Connection)
5. First. You're going to need to find his
IP or host name. Either will work. If you
are on mIRC You can get it by typing /
whois (nick) ...where (nick) is the persons
nickname without parenthesis. you will
either get a host name or an IP. copy it
down. If you do not get it or you are not
using mIRC then you must direct connect
to their computer or you may use a sniffer
to figure out his IP or host name. It's
actually better to do it without the sniffer
because most sniffers do not work now-
a-days. So you want to establish a direct
connection to their computer. OK, what is
a direct connection? When you are:
Sending a file to their computer you are
directly connected.
AOL INSTANT MESSENGER allows a
Direct Connection to the user if accepted.
ICQ when sending a file or a chat request
acception allows a direct connection.
Any time you are sending a file. You are
directly connected. (Assuming you know
the user is not using a proxy server.)
Voice Chatting on Yahoo establishes a
direct connection.
If you have none of these programs,
either i suggest you get one, get a sniffer,
or read this next statement.
If you have any way of sending thema link
to your site that enables site traffic
statistics, and you can log in, send a link
to your site, then check the stats and get
the IP of the last visitor. It's a simple and
easy method i use. It even fool some
smarter hackers, because it catches them
off guard. Anyway, once you are directly
connected use either of the two methods i
showed you earlier and get into DOS.
Type NETSTAT -n. NETSTAT is a program
that's name is short for NET STATISTICS.
It will show you all computers connected
to yours. (This is also helpful if you think
you are being hacked by a trojan horse
and is on a port that you know such as
Sub Seven: 27374.) Your screen should
look like this showing the connections to
your computer:
------------------------------------------------------------------------------------------------
C:\WINDOWS\DESKTOP>netstat -n
Active Connections
Proto Local Address Foreign Address
State
TCP 172.255.255.82:1027
205.188.68.46:13784 ESTABLISHED
TCP 172.255.255.82:1036
205.188.44.3:5190 ESTABLISHED
TCP 172.255.255.82:1621
24.131.30.75:66 CLOSE_WAIT
TCP 172.255.255.82:1413
205.188.8.7:26778 ESTABLISHED
TCP 172.255.255.82:1483
64.4.13.209:1863 ESTABLISHED
C:\WINDOWS\DESKTOP>
------------------------------------------------------------------------------------------------
The first line indicated the Protocol
(language) that is being used by the two
computers.
TCP (Transfer Control Protocol) is being
used in this and is most widely used.
Local address shows your IP address, or
the IP address of the system you on.
Foreign address shows the address of the
computer connected to yours.
State tells you what kind of connection is
being made ESTABLISHED - means it will
stay connected to you as long as you are
on the program or as long as the
computer is allowing or is needing the
other computers connection to it.
CLOSE_WAIT means the connection
closes at times and waits until it is
needed or you resume connection to be
made again. One that isn't on the list is
TIME_WAIT which means it is timed. Most
Ads that run on AOL are using TIME_WAIT
states.
the way you know the person is directly
connected to your computer is because of
this:
------------------------------------------------------------------------------------------------
C:\WINDOWS\DESKTOP>netstat -n
Active Connections
Proto Local Address Foreign Address
State
TCP 172.255.255.82:1027
205.188.68.46:13784 ESTABLISHED
TCP 172.255.255.82:1036
205.188.44.3:5190 ESTABLISHED
TCP 172.255.255.82:1621
24.131.30.75:66 CLOSE_WAIT
TCP 172.255.255.82:1413 abc-123-
ppp.webnet.com ESTABLISHED
TCP 172.255.255.82:1483
64.4.13.209:1863 ESTABLISHED
C:\WINDOWS\DESKTOP>
------------------------------------------------------------------------------------------------
Notice the host name is included in the
fourth line instead of the IP address on
all. This is almost ALWAYS, the other
computer that is connected to you. So
here, now, you have the host name:
abc-123-ppp.webnet.com
If the host name is not listed and the IP is
then it NO PROBLEM because either one
works exactly the same. I am using
abc-123-ppp.webnet.com host name as
an example. Ok so now you have the IP
and/or host name of the remote system
you want to connect to. Time to hack!
Open up your DOS command. Open up
NBTSTAT by typing NBTSTAT. Ok, there's
the crap again. Well, now time to try out
what you have leanred from this
document by testing it on the IP and/or
host name of the remote system. Here's
the only thing you'll need to know.
IMPORTANT, READ NOW!!!
-a (adapter status) Lists the remote
machine's name table given its name
-A (Adapter status) Lists the remote
machine's name table given its IP
address.
Remember this?
Time to use it.
-a will be the host name
-A will be the IP
How do i know this?
Read the Statements following the -a -A
commands. It tells you there what each
command takes.
So have you found which one you have to
use?
GOOD!
Time to start.
Using it to your advantage
6. Type this if you have the host name
only.
NBTSTAT -a (In here put in hostname
without parenthesis)
Type this is you have the IP address only.
NBTSTAT -A (In here put in IP address
without parenthesis)
Now, hit enter and wait. Now Either one of
two things came up
1. Host not found
2. Something that looks like this:
--------------------------------------------
NetBIOS Local Name Table
Name Type Status
---------------------------------------------
GMVPS01 <00> UNIQUE Registered
WORKGROUP <00> GROUP Registered
GMVPS01 <03> UNIQUE Registered
GMVPS01 <20> UNIQUE Registered
WORKGROUP <1E> GROUP Registered
---------------------------------------------
If the computer responded "Host not
found" Then either one of two things are
the case:
1. You screwed up the host name.
2. The host is not hackable.
If number one is the case you're in great
luck. If two, This system isn't hackable
using the NBTSTAT command. So try
another system.
If you got the table as above to come up,
look at it carefully as i describe to you
each part and its purpose.
Name - states the share name of that
certain part of the computer
<00>, <03>, <20>, <1E> - Are the
Hexidecimal codes giving you the services
available on that share name.
Type - Is self-explanatory. It's either
turned on, or activated by you, or always
on.
Status - Simply states that the share
name is working and is activated.
Look above and look for the following
line:
GMVPS01 <20> UNIQUE Registered
See it?
GOOD! Now this is important so listen up.
The Hexidecimanl code of <20> means
that file sharing is enabled on the share
name that is on that line with the hex
number. So that means GMVPS01 has file
sharing enabled. So now you want to
hack this. Here's How to do it. (This is the
hard part)
LMHOST File
7. There is a file in all Windows systems
called LMHOST.sam. We need to simply
add the IP into the LMHOST file because
LMHOST basically acts as a network,
automatically logging you on to it. So go
to Start, Find, FIles or Folders. Type in
LMHOST and hit enter. when it comes up
open it using a text program such as
wordpad, but make sure you do not leave
the checkmark to "always open files with
this extension" on that. Simply go through
the LMHOST file until you see the part:
# This file is compatible with Microsoft
LAN Manager 2.x TCP/IP lmhosts
# files and offers the following
extensions:
#
# #PRE
# #DOM:
# #INCLUDE
# #BEGIN_ALTERNATE
# #END_ALTERNATE
# \0xnn (non-printing character support)
#
# Following any entry in the file with the
characters "#PRE" will cause
# the entry to be preloaded into the name
cache. By default, entries are
# not preloaded, but are parsed only after
dynamic name resolution fails.
#
# Following an entry with the "#DOM:"
tag will associate the
# entry with the domain specified by .
This affects how the
# browser and logon services behave in
TCP/IP environments. To preload
# the host name associated with #DOM
entry, it is necessary to also add a
# #PRE to the line. The is always
preloaded although it will not
# be shown when the name cache is
viewed.
#
# Specifying "#INCLUDE " will force the
RFC NetBIOS (NBT)
# software to seek the specified and parse
it as if it were
# local. is generally a UNC-based name,
allowing a
# centralized lmhosts file to be
maintained on a server.
# It is ALWAYS necessary to provide a
mapping for the IP address of the
# server prior to the #INCLUDE. This
mapping must use the #PRE directive.
# In addtion the share "public" in the
example below must be in the
# LanManServer list of
"NullSessionShares" in order for client
machines to
# be able to read the lmhosts file
successfully. This key is under
# \machine\system\currentcontrolset
\services\lanmans erver\parameters
\nullsessionshares
# in the registry. Simply add "public" to
the list found there.
#
# The #BEGIN_ and #END_ALTERNATE
keywords allow multiple #INCLUDE
# statements to be grouped together. Any
single successful include
# will cause the group to succeed.
#
# Finally, non-printing characters can be
embedded in mappings by
# first surrounding the NetBIOS name in
quotations, then using the
# \0xnn notation to specify a hex value
for a non-printing character.
Read this over and over until you
understand the way you want your
connection to be set. Here's an example
of how to add an IP the way I would do it:
#PRE #DOM:255.102.255.102
#INCLUDE
Pre will preload the connection as soon
as you log on to the net. DOM is the
domain or IP address of the host you are
connecting to. INCLUDE will automaticall
set you to that file path. In this case as
soon as I log on to the net I will get
access to 255.102.255.102 on the C:/
drive. The only problem with this is that
by doin the NETSTAT command while you
are connected, and get the IP of your
machine. That's why it only works on
simple PC machines. Because people in
these days are computer illiterate and
have no idea of what these commands
can do. They have no idea what NETSTAT
is, so you can use that to your advantage.
Most PC systems are kind of hard to hack
using this method now because they are
more secure and can tell when another
system is trying to gain access. Also,
besure that you (somehow) know whether
they are running a firewall or not because
it will block the connection to their
computer. Most home systems aren't
running a firewall, and to make it better,
they don't know how operate the firewall,
therefore, leaving the hole in the system.
To help you out some, it would be a great
idea to pick up on some programming
languages to show you how the computer
reads information and learn some things
on TCP/IP (Transfer Control Protocol/
Internet Protocol) If you want to find out
whether they are running a firewall,
simply hop on a Proxy and do a port scan
on their IP. You will notice if they are
running a firewall because most ports are
closed. Either way, you still have a better
chance of hacking a home system than
hacking Microsoft.
Gaining Access
7. Once you have added this to you
LMHOST file. You are basically done. All
you need to do is go to:
Start
Find
Computer
Once you get there you simply type the IP
address or the host name of the system.
When it comes up, simply double click it,
and boom! There's a GUI for you so you
don't have to use DOS anymore. You can
use DOS to do it, but it's more simple and
fun this way, so that's the only way i put
it. When you open the system you can
edit, delete, rename, do anything to any
file you wish. I would also delete the
command file in C:/ because they may
use it if they think someone is in their
computer. Or simply delete the shortcut to
it. Then here's when the programming
comes in handy. Instead of using the
NBTSTAT method all the time, you can
then program you own trojan on your
OWN port number and upload it to the
system. Then you will have easier access
and you will also have a better GUI, with
more features. DO NOT allow more than
one connection to the system unless they
are on a faster connection. If you are
downloading something from their
computer and they don't know it and their
connection is being slow, they may check
their NETSTAT to see what is connected,
which will show your IP and make them
suspicious. Thats it. All there is to it. Now
go out and scan a network or something
and find a computer with port 21 or
something open.
I think I understood the 1st part and mb I
can understand the 2nd, but I will mb
need help, and I think this is the good
place to ask
I would like to know some things:
If the other guy knows about hack, will
trying this method enable him to change
things on your computer?
If the guy has some firewall, will it block
all?
May this method arm my pc?
Is the risk of being detected and punished
important?
Can I stop all links between my pc and
my victim's pc after I changed some
things?
Thanks a lot for any help :')
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment